ARRIS C250 V2 FPV in all version comes with ARRIS C250 V2 RTF, MINI B6 charger with adaptor, Fatshark Attitude V4 fpv goggle.It is fully assembled, tuned and tested before leaving the factory. C250 V2 is one more professional 250 fpv racing drone produced by ARRIS on the basis of the ARRIS C250. The same as the ARRIS C250, the C250 V2 has the advantage of simple structure and high strength. In the meanwhile, ARRIS C250 V2 adopts 4in1 30A tower for the first time, improve the performance of the drone much.Take it to start your FPV journey.
1. Simple structure frame installed with tower structure ESC/PDB, easy to assemble and easy to repair.
2. High quality 3K Carbon fiber frame, the material is imported from Janpan
3. 4mm thick arms, super strong and durable
4. Super Light frame, only $136g
5. The tower ESC/FC comes with integrated OSD, no need to install it separately
6. The angle of the FPV camera is adjustable
7. 4mm thick arms, super strong and durable
8. High efficiency X2205 2300KV motor provides you better performance and longer working life
9. High quality 5042 3 blade propeller, 10% higher efficiency than normal propellers
10. High safety 4S 1500mah 50C lipo battery
Dimension:195mm x 230mm x 42mm (Propellers not included)
Diagonal Wheelbase: 250mm
Flight Controller: F3 flight Controller
Frame Material: Pure Carbon fiber
Radio System: Radiolink AT9 with R6DSM receiver
Camera: ARRIS XAT700M FPV Mini Camera
FPV TX: 5.8G 200mw 40CH
Antenna: 5.8G Antenna
Flying Time: 10min hovering
Battery: ARRIS 4S 1500mah 50C Lipo
Charger: Imax B6 Mini Charger with adaptor
Goggle: Fatshark Attitude V4 FPV Goggle
ARRIS C250 V2 is made of pure carbon fiber material. The upper plate and side plate adopts 1.5mm pure carbon fiber material, decrease the weight of the whole frame. Meanwhile, the motor arm adopts 4mm carbon fiber material, ensure the strength of the frame. The total weight of the frame is about 137g.With the simplify one-piece design and lower gravity center design, all kinds of flight actions can be done with facility.
The layout design of the C250 V2 is reasonable, the standard flight controller and PDB board can install there.On the frame, there is reserved space for the XT60 female battery connector.The motor arm has holes for 220x series motors, and both 5 inches and 6 inches propellers can install on the C250 V2 frame.
The main advantages of the 4in1 30A Tower:
1. With the double layer design, you just need to plug the pins between esc and flight controller, flight controller and other electronic components. The layout is more concise, decrease the weight of the drone, provided guarantee for flight performance improvements.
The power for flight controller and camera is provided by the BEC on the flight controller. The power for video transmitter is provided by battery. This improves the anti-interference of the video transmission.
2. The tower integrated the OSD, avoid to install it additionally and the adjustment.The drone could get a quick response to the throttle during the flight.
3. The Tower structure design protects the ESC well during the flight. According to our experience, some of the ESC were damaged by the propeller rotation or tree brunch cut, and some of the ESC were damaged due to the broken of the motor arm during the crash when it installed on top of the motor arm. Sometimes, in order to protect the ESC, we added ESC cover to protect it. From this, the weight of the drone increased. For this tower, the esc integrated in the tower which installed in the middle of the quad frame, the ESCs can be protected quite well and make it looks better.
With the high performance ARRIS X2205 2300KV brushless motor, the ARRIS C250 V2 has outstanding power.
1. Adopts the brand new M5 steel shaft, improving the structure strength.
2. Anti-slip pro design.
3. Upgrade to centrifugal fan design, optimizing the heat dissipation.
4. Adopts original Japan NSK bearing, improving the performance of the motor.
5. Adopts N52 tile-shaped magnets.
6. The motor passed more than 20 kinds of tests before leaving the factory, ensure the quality of the motor.
The ARRIS C250 V2 adopts with the latest 5042 propeller, it has bigger windward area, well balance and strengthen root, and the efficiency is 10% higher than normal propeller. This propeller is the first choice of FPV racing drones.
ARRIS XAT700M FPV Mini Camera for FPV Racing Drones--ARRIS XAT700M HS1177 fpv mini camera is specially designed for FPV. This camera performs well in both bright and dark condition with 700TVL high quality image. And the camera angle on the drone is adjustable.
ARRIS 5.8g 200mW 40-CH video TX and antenna pre-assembled.The ARRIS TS5823L with LED is transmitting a full range of 40 channels and only weighs 10g. It's perfect for a wide range of aircraft!With a goggle or monitor in hand, you can begin your FPV journey.
ARRIS X-Speed C250 V2 has integrated with a remote controller battery warning buzzer, pilot can set the threshold (adjustable) according to CF parameter-adjustment software. In addition, you can also locate your racing drone through triggering the buzzer with the switch D on the transmitter.
Self-level mode is the easiest to fly, because when you leave the stick at the center and not controlling it, your drone just level itself and stays there.This mode is good for beginners.
Manual mode is useful for acrobatics such as flips or rolls, or FPV when smooth and fast control is desired. The picture below is what we set on our own Radiolink AT9 Radio.
RadioLink AT9 9-Channel 9CH 2.4GHz Transmitter + R9D Receiver.The AT9 radio is with high performance-price ratio. And it can support strength, receiver voltage monitored, extending battery voltage, temperature, motor RPM, GPS etc.
High safety ARRIS 4S 1500mah Lipo Battery
ARRIS 4S 1500mAh 50C lipo battery is specially designed for FPV racer. The price of this battery is much higher than the similar batteries in the market, because we only sell top-quality batteries. As we all know, the low quality battery might have potential safety hazard, we will never tolerate such products.For ARRIS 4S 1500mah lipo battery, we have done UN38.3 test,1.2M Drop test,MDS report for it, for the test report, you can check here.
SKYRC B6 mini Charger is a high-performance, micro processor control charge/discharge station with battery management suitable for use with all current battery types, with integral equalizer for six-cell Lithium- Polymer (LiPo), Lithium-Ferrum (LiFe) and Lithium-Ion (LiIon) batteries; maximum 6A charge current and maximum 60W charge power.
Input voltage: DC11-18V
Circuit power: Max Charge (60W)
Discharge power: 5W
Charge current range: 0.1-6.0A
Discharge current range: 0.1-2.0A
LiPo/LiFe/Lilon Cells: 1-6S
NiMH/NiCd Cells: 1-15S
Pb battery voltage: 1-10P (2-20V)
Net weight: 237g
Dimensions: 107 x 85 x 34mm
Fat Shark Attitude V4 FSV1048 10th anniversary edition integrated with OLED display modular receiver, DVR recording/playback and 3-axis head tracking.
Commemorate Fat Shark’s 10th year with the brand new AttitudeV4 Anniversary Edition headset, which combines a consumer-favorite 32°field of view (FOV), 4:3 VGA display and specialty pricing. This limited edition of red-trimmed goggles comes with a digital video recorder (DVR) and an included, 5.8G OLED receiver make to make the Attitude V4 a classic FPV headset. The included, simple-to-use receiver has one-touch band change capability, channel scanning and a spectrum analyzer for clean and simple channel selection. The Attitude V4 also brings back 9 degree, 3 axis headtracking (data cables sold separately).
|FOV (field of view):
||32°diagonal (Image size: 1.3m @ 2m)
||Plastic optic module
|Interpupillary Distance (IPD):
||59 to 69 mm (adjustable)
|Optional Diopter Lens Inserts:
||-2, -4, -6 dpt
||Full color LCD polarized LED backlit
|Binocular display (640 X 480 VGA)
|NTCS/PAL auto selecting
||Stereo (Requires adjustable volume earphone)
||Channel selection/ head tracker reset
|Mode selection (wired/wireless)
|Contrast/ brightness control
||7 - 13 V (2S/3S supply)
|220mA direct mode (RX off) (@7.4V nominal)
||7.4V, 1000mAh Li-po battery with LED indicator
||Analog Video Recording (no audio or HD recording)
|MicroSD support to 32 GB
|Record Rate: 6Mbps (MJPG compression, 30 fps, AVI)
|File playback (native recording, no codec support)
|Upgradeable via SD card
|PAL/NTSC continuous scan auto detect/mode change
|Auto save if power removed
|RF Modules (Optional):
||multi channel and band support (modular RF)
||3.5mm AV in/out port
|Power in port
|3.5mm stereo earphone port
|Mini DIN head tracker data port
||5G8 32ch RaceBand RF module with OLED display
|5G8 SpiroNET CP antenna
|7.4V, 1000mAh Li-po battery with LED indicator
|Battery discharge adapter
||Ergonomic molded headset w/ adjustable headband
||168 x 83 x 71mm
||616g, 202 x 139 x 100mm
1 x ARRIS C250 V2 Racing Quad Frame
4 x ARRIS X2205 V2 2300KV Brushless Motors
1 x Flycolor Tower w/ F390 30A 4 in 1 ESC + F3 + OSD + PDB
4 x ARRIS 5042 3-blade Propeller
1 x ARRIS XAT700M FPV camera
1 x 5.8G 200mw 32CH FPV TX
1 x FPV Transmitter Antenna
1 x Radiolink AT9 Transmitter with receiver
1 x ARRIS Buzzer
1 x ARRIS 4S 1500mah Lipo Battery
1 x Skyrc B6 mini Charger
1 x Skyrc B6 mini charger adaptor
1 x Fatshark Attitude V4 FPV Goggle
Note: You will receive two parcels, one with the goggle and one with the rest of the items. Due to the battery in the parcel, the shipping time might be longer than usual.