SP Racing F3 Flight Controller Acro 6 DOF/Deluxe 10 DOF for RC Multicopter With Shell

SP Racing F3 Flight Controller Acro 6 DOF/Deluxe 10 DOF for RC Multicopter With Shell

Item# NA0015-16
USD $23.99
  • DESCRIPTION
  • REVIEWS
Version: 
QTY:

SP Racing F3 Flight Controllerl for RC Multicopter

This flight controller is integrated with barometer, gyroscope, accelerometer, magnetometer, can also extend some functions such as GPS, LED strips, sonar, etc. It is a flight controller specially designed for FPV racing drones, can achieve operation such as positioning, rolling, etc.

Features:
Practical - Easy to access connectors and solder pads.
Configurable - Choose to use connectors, solder pads or pins.
Stackable - Mount to your PDB or OSD.
Compact - Only 36x36mm.
Professional - Symmetrical, Neat and Tidy.
8 Dedicated PWM outputs
8 PWM Inputs
36 I/O Connections
72Mhz Clock Speed
3 Hardware Serial Ports
64Mb Flash Storage

Specification (Acro 6DOF Version and 10DOF Duluxe Version):
The hardware was designed by the lead developer of Cleanflight to be more capable than the previous-generation STM32F1-based boards after hearing feedback from the Cleanflight users, contributors and top-pilots.
36x36mm board with 30.5mm mounting holes
Weight: 6 grams
Acro version is without Compass and Barometer Sensors
STM32F303 CPU, 72Mhz inc FPU
High-Capacity Flash (Acro and Deluxe)
MPU6050 accelerometer/gyro
MS5611 barometer (Deluxe only)
HMC5883 compass (Deluxe only)
MicroUSB socket
2 x 8pin JST-SH sockets (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)
8 x 3pin though-holes for pin headers for ESC/Servo connections
2 x 4pin though-holes for pin headers for 2x serial ports
1 x 2pin though-holes for pin headers for battery voltage
1 x 2pin though-holes for pin headers for buzzer
1 x 4pin JST-SH socket for I2C
1 x 4pin JST-SH socket for SWD debugging

Flight Performance
The SPRacingF3 builds on tried and tested software, processor and sensor technology to make your aircraft fly like it's on rails.

No-Compromise I/O
Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + Sonar + 8 motors - all at the same time.

Configurable
The SPRacingF3 runs Cleanflight which can be configured to suit your needs using a cross-platform GUI (Windows/OSX/Linux).

Tiny and lightweight
The SPRacingF3 has a standard 36x36mm form-factor with 30.5mm mounting holes and weighs just 6 grams.

Flight Logging
On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup without guesswork.

Next-Generation CPU
The SPRacingF3 has an ARM Cortex-M4 72Mhz CPU with Math co-processor (FPU) for efficient flight calculations that gets more done in less time.
Loop times up to ~2x as fast as previous-generation STM32F1 based boards.

Developer Friendly
Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.

OneShot ESC
Full support for OneShot ESCs for easy PID tuning and a sharper response.

Broad RC receiver Support
Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. No external inverters required (built-in).

Programmable LED
Dedicated output for programmable LEDs - great for orientation, racing and night flying.

Battery Monitoring
Battery monitoring ports for voltage and current.

Sonar
Sonar support for precision low-altitude hold.

I2C Port
I2C port always powered, perfect for external sensors or always-on OLED Screen.

Buzzer
Buzzer port for audible warnings and notifications.